Tools

Hand pliers designed specifically for Lockit™ Strain Relief Bushings (excluding ST201N).

Hand pliers for Heyco Strain Relief Bushings SR 7N-2 and SR 8N-2.

Pre-assembly equipment for Heyco Assembly-Friendly Lockit Series Strain Reliefs.

Replacement hand grips for pliers 0022.

Replacement hand grips for pliers 0030.

Replacement nut for pliers 0022 and 0030.

Replacement screw for pliers 0022 and 0030.

Replacement spring for pliers 0022 and 0030.

These pneumatic drive rivet tools are especially suited for hard to reach or delicate assemblies encountered on all kinds of mechanical and electrical components, appliances, P.C. board assemblies, relays, switches, controls, etc. Feature an easy-grip, non-slip, straight case for single hand fatigue free operation and is equipped with a suspension bail for overhead connections on bench type precision assemblies. Can be safely used in all positions. There is no need to pre-drive rivets.

Staking kits for single end terminals, eyelets or rivets. Kits Include: Anvil Holder, Swaging tools for .062" (1.57mm) to .125" (3.2mm) swage diameter, Anvils for .070" (1.78mm) to .152" (3.86mm) via Solder Turrets.

These kits provides all of the components needed to stake most terminals, standoffs, eyelets or rivets. These kits include: Anvil Holder, Swaging tools for .062" (1.57mm) to .180" (4.8mm) swage diameter, Swaging tool for .051" (1.30mm) to .098" (2.49mm) diameter double ended turret terminals, Anvils for swage standoffs / spacer, Anvils fro forked turret terminals and Spring loaded receding pins.

Anvils for fork type terminals. Accepts Diameter of 3/32" (2.38mm) to 5/32" (3.97mm) at one end and diameter of 3/16" (4.76mm) other end. .040" (1.02mm) slot one end and .060" (1.52mm) slot at other end.

Hold .250" (6.4mm) diameter anvils for use in drill or arbor press. For use in vices, Arbors, kickpresses, punch presses etc. Include a holder, 2 washers and wing nut plus instructions. May be used with receding pins & springs for eyelet assembly.

.069" (1.75mm) Diameter receding pins to be used with the following products: Anvil holder K1719, Anvil K1722 and Return spring K1321.

.045" (1.14mm) Diameter receding pins to be used with the following products: Anvil holder K1719, Anvil K1722 and Return spring K1321.

Staking tool for Single End terminals, Eyelets or Rivets. For Double End (Feed Thru) terminals. Fits .180" (4.57mm) through .190" (4.83mm) diameter shanks. Hole in Tool fits over pin head and securly stakes the rivet part of the terminals.

The top ends of swage staking tools for .062" (1.57mm) to 0.98" (2.49mm) diameter shanks. For Single End terminals, Eyelets or Rivets.

The top ends of swage staking tools for .110" (2.79mm) to .125" (3.18mm) diameter shanks. For Single End terminals, Eyelets or Rivets.

Micro Plastics' Adjustable Ergonomic Strain Relief Tool has been carefully designed to help reduce the wrist fatigue associated with bushing installation. The handles are preset to a specified angle, allowing the hand and wrist of the operator to naturally align during normal use. This tool is fully adjustable and will install all size of micro plastics strain relief bushings.

Ajustable assembly tool for strain relief bushes. Suits mounting hole diameters 9.5mm to 19mm.

Set of tools including: Top Staking Tool (K1324) and Anvil (K1309).

Set of tools including: Top Staking Tool (K1324) and Anvil (K1325).

Set of tools including: Top Staking Tool (K1715) and Anvil (K1309).

Set of tools including: Top Staking Tool (K1715) and Anvil (K1326).

Set of tools including: Top Staking Tool (K1714) and Anvil (K1716).

Set of tools including: Top Staking Tool (K1714) and Anvil (K1726).

Set of tools including: Top Staking Tool (K1715) and Anvil (K1717).

23mm wide double-sided adhesive tape for fastening needs. Roll holds 100m of tape.

14mm wide double-sided adhesive tape for fastening needs. Roll holds 100m of tape.

18mm wide double-sided adhesive tape for fastening needs. Roll holds 100m of tape.

8mm wide double-sided adhesive tape for fastening needs. Roll holds 100m of tape.

12mm wide double-sided adhesive tape for fastening needs. Roll holds 100m of tape.

28mm wide double-sided adhesive tape withfoam for when padding is needed. Foam also allows tape to replace worn adhesive on products such as cable tie mounts. Roll holds 50m of tape.

8mm wide double-sided adhesive tape withfoam for when padding is needed. Foam also allows tape to replace worn adhesive on products such as cable tie mounts. Roll holds 50m of tape.

18mm wide double-sided adhesive tape withfoam for when padding is needed. Foam also allows tape to replace worn adhesive on products such as cable tie mounts. Roll holds 50m of tape.

23mm wide double-sided adhesive tape withfoam for when padding is needed. Foam also allows tape to replace worn adhesive on products such as cable tie mounts. Roll holds 50m of tape.

13mm wide double-sided adhesive tape withfoam for when padding is needed. Foam also allows tape to replace worn adhesive on products such as cable tie mounts. Roll holds 50m of tape.

High quality retractable tape measure.

High quality retractable tape measure.

High quality retractable tape measure.

High quality retractable tape measure.

High quality retractable tape measure.

High quality retractable tape measure.

Crimp tool for Pre-Insulated terminals. Suits cables sized 0.5 to 6.0 mm².

Crimp tool for Pre-Insulated terminals. Suits cables sized 0.5 to 6.0 mm².

High quality combination hand tool designed to crimp all terminals and connectors in the 22 - 10 AWG wire range both non-insulated and insulated. Has a wire cutter up front, strips 22 - 10 AWG wire and has a built in bolt cutter for #4 to #10 threads.

Designed to install .250 (6.35mm) male quick-fit terminals quickly and easily. Insert terminals into slot. Spring clip will Align terminals with mounting holes. Hold terminals securely for positioning and press-fit to secure firmly in place. Lift tool to release terminals. Current rating: 15 Amps.

Finishing tap to apply PG-7 threading to holes. Use at the bottom of the thread. Flank angle 80°. Made of high-speed steel with ground threads for greater accuracy to assure liquid tightness.

Finishing tap to apply PG-13.5 threading to holes. Use at the bottom of the thread. Flank angle 80°. Made of high-speed steel with ground threads for greater accuracy to assure liquid tightness.

Finishing tap to apply PG-11 threading to holes. Use at the bottom of the thread. Flank angle 80°. Made of high-speed steel with ground threads for greater accuracy to assure liquid tightness.